Включение SMART для HDD с помощью smartctl

Как писал ранее начал мониторить работу хддешек с помощью smartctl, но вот беда, добравшись до очередного сервера, и запустив привычное smartctl -a /dev/имя устройства, получил следующую бяку:

# smartctl -a /dev/ad10
smartctl 5.40 2010-10-16 r3189 [FreeBSD 8.2-RELEASE amd64] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Caviar Green (Adv. Format) family
Device Model:     WDC WD15EARS-00Z5B1
Serial Number:    WD-WMAVU3360943
Firmware Version: 80.00A80
User Capacity:    1 500 301 910 016 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   8
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Thu Jun 23 12:25:20 2011 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Disable


т.е.
SMART support is: Available — device has SMART capability. — смарт доступен для этого винта
SMART support is: Disable — но блин выключен)))
Включить его еще проще чем мониторить:

# smartctl -s on /dev/ad10
smartctl 5.40 2010-10-16 r3189 [FreeBSD 8.2-RELEASE amd64] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.

ну и далее привычное:

# smartctl -a /dev/ad10
smartctl 5.40 2010-10-16 r3189 [FreeBSD 8.2-RELEASE amd64] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Caviar Green (Adv. Format) family
Device Model:     WDC WD15EARS-00Z5B1
Serial Number:    WD-WMAVU3360943
Firmware Version: 80.00A80
User Capacity:    1 500 301 910 016 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   8
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Thu Jun 23 12:28:25 2011 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status:  (0x84) Offline data collection activity
                                        was suspended by an interrupting command from host.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                 (31800) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 255) minutes.
Conveyance self-test routine
recommended polling time:        (   5) minutes.
SCT capabilities:              (0x3031) SCT Status supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   100   253   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   182   182   021    Pre-fail  Always       -       5858
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       137
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   093   093   000    Old_age   Always       -       5347
 10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       136
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       131
193 Load_Cycle_Count        0x0032   140   140   000    Old_age   Always       -       181043
194 Temperature_Celsius     0x0022   108   106   000    Old_age   Always       -       42
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   200   200   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   200   200   000    Old_age   Offline      -       0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Поделись с друзьями:

Опубликовано 23.06.2011 в 09:41 · Автор komivlad · Ссылка
Рубрики: FreeBSD · Теги: , , , ,

Написать комментарий